Before you begin…
Make sure you've received all three boxes that The Bed is delivered in. If you're missing one or two of the boxes, please refer to your shipping confirmation email and click into your FedEx multi-piece tracking number which will be able to show you a detailed view of the three separate boxes in transit. On rare occasions, these boxes can arrive at different times (our apologies as this is unfortunately out of our control!). If you do have any questions, please don’t hesitate to shoot us a note at help@thuma.co and we'll be in touch as quickly as possible.
assembly instructions
Let’s get together.
Start with Box 1 of 3. Flip upside down and cut the tape around the bottom of the box. Flip right side up, and slide the top of box off. Repeat with Box 2. Carefully take all pieces out of their packaging. Save Box 3 for later.
See step-by-step guideassembly instructions
Let’s get together.
Start with Box 1 of 3. Flip upside down and cut the tape around the bottom of the box. Flip right side up, and slide the top of box off. Repeat with Box 2. Carefully take all pieces out of their packaging. Save box 3 for later.
See step-by-step guide-
Step 1
Lay out the pieces where you want your bed.
Arrange Long Rails (sides) with “U” joints facing out and Short Rails (wall and foot) with “U” joints facing in. Step into the center of the frame.
Keep the Slats on the sideline for now.
-
Step 2
A. Pick a corner to start. Stand up first Leg, and insert Long Rail into joint. Make sure the “U” joint is facing up.
B. While balancing Leg and Long Rail, pick up Short Rail and insert joint with “U” facing down.
C. Rest the ends of both rails opposite the joint on the floor.
Hint: Angle Leg and Long Rail towards Short Rail for smoothest fit
-
Step 3
A. Move along the Short Rail to the next corner. Stand up second Leg, and insert Long Rail into joint. Make sure the “U” joint is facing up.
B. Slide Leg and Long Rail under Short Rail, creating second joint.
Ya baby...half way there!
-
Step 4
A. Mosey down to the next corner. Place the third Leg into Long Rail.
B. Repeat with fourth Leg.
-
Step 5
Place second Short Rail into the third and fourth Legs.
-
Step 6
A. Screw the Center Leg into the Center Rail.
B. Place Center Rail inside of the horseshoes on the inside of the frame.
C. Take Screws and hand tighten through the Short Rail into the Center Rail.
-
Step 7
A. Lay rolled Slats down at the head of the bed. Place the first slat between Short Rail and slat stop to hold in place.
B. Roll ‘em down to the other end. Place last slat between Short Rail and slat stop to hold tight.
-
Step 8
A. The Center Leg doubles as a leveler. Adjust up and down, as needed.
B. Place your mattress on top of The Bed.
C. Slide The PillowBoard between the mattress and the back wall.
And you’re all set!
-
Step 1
Lay out the pieces where you want your bed.
Arrange Long Rails (sides) with “U” joints facing out and Short Rails (wall and foot) with “U” joints facing in. Step into the center of the frame.
Keep the Slats on the sideline for now.
-
Step 2a
Pick a corner to start. Stand up first Leg, and insert Long Rail into joint. Make sure the “U” joint is facing up.
-
Step 2b
While balancing Leg and Long Rail, pick up Short Rail and insert joint with “U” facing down.
-
Step 2c
Rest the ends of both rails opposite the joint on the floor.
Keep the Slats on the sideline for now.
-
Step 3a
Move along the Short Rail to the next corner. Stand up second Leg, and insert Long Rail into joint. Make sure the “U” joint is facing up. .
-
Step 3b
Slide Leg and Long Rail under Short Rail, creating second joint.
Ya baby... half way there!
-
Step 4
A. Mosey down to the next corner. Place the third Leg into Long Rail.
B. Repeat with fourth Leg.
-
Step 5
Place second Short Rail into the third and fourth Legs.
-
Step 6a
Screw the Center Leg into the Center Rail.
-
Step 6b
Place Center Rail inside of the horseshoes on the inside of the frame.
-
Step 6c
Take Screws and hand tighten through the Short Rail into the Center Rail.
-
Step 7a
Lay rolled Slats down at the head of the bed. Place the first slat between Short Rail and slat stop to hold in place.
-
Step 7b
Roll ‘em down to the other end. Place last slat between Short Rail and slat stop to hold tight.
-
Step 8
A. The Center Leg doubles as a leveler. Adjust up and down, as needed.
B. Place your mattress on top of The Bed.
C. Slide The PillowBoard between the mattress and the back wall.
And you’re all set!